Times are pretty lean out there for the average homeowner so it is important that you get the best deals possible whether you are looking to get some tiling done, be it wall tiling, floor tiling, a full bathroom renovation, simply tiling your kitchen worktop areas or regrouting to spruce up some existing tiling or putting a silicone sealant trim in place to stop leaks from shower cubicles.
Go direct to the trades suppliers - get wholesale prices for tiling materials
The first thing to remember when buying materials is that you really are better off getting trade prices. Even the wholesalers and suppliers who provide materials to tilers and bathroom installer tradesmen are struggling in these very difficult financial times so it is always worth asking the likes of Travis Perkins, Builder Center, Tile Center, Jewsons and any other local builders merchants whether they deal with the public and what type of discounts are available to the homeowner. You will find that nowadays they simply do not care who they sell materials to, as long as you are prepared to help pay their bills.
Another option is to find a tiler and ask him whether you can buy the materials through his trade account if he has one with suppliers mentioned above such as Travis Perkins. You can pay the account for him and get the materials sometimes at very attractive trade discount prices.
Consider Screwfix for tiling materials - Buy tiling materials where the trade buys
They provide materials at trade prices but they are not just for tilers or tradesmen. They target the tiler and tradesmen market but they have outlets which anyone can walk into now in most cities. They are part of B & Q so you should get your materials there but often pay less than you would in B And Q stores. They have a very good website where you can buy online and also you can go to their site and check for branches.
Ask for discounts - don't be afraid to haggle for reduced materials prices. The construction industry (including tilers) is going through a very hard time and many may consider it is better to get a deal than not even if they give the tiler materials away cheap to you.
Look for cheap materials for jobs in the right month
It will be far cheaper general speaking to buy materials for tiling jobs in the early part of the year. January is a good time to start looking for materials as there are many discounts. Again, the tiler and construction trades industry has a difficult time at this time of year so you are likely to get some good deals even if you are not looking to get your tiling jobs done until later on.
Showing posts with label quotes. Show all posts
Showing posts with label quotes. Show all posts
19 Jan 2010
10 Sept 2009
How To Bleed Radiators - Plumbing Tips By Top Tradespeople
How To Save Money On Your Plumbing Bills
In tough financial times it is important to try to save money on unnecessary home improvement bills for jobs which with a little bit of ‘insider’ knowledge you can do yourself to a very satisfactory standard. Minor jobs like bleeding radiators can save you substantial amounts of money on unncessary plumbing bills.
Bleeding A Radiator
Occasionally, you will notice a radiator heating unevenly. Specifically, the bottom of the radiator is warm while the top is cool. Before you call a heating engineer or plumber, try the simple and inexpensive remedy of bleeding the radiator to see if this will fix the problem. A radiator needs bleeding when air has infiltrated the system and is blocking the warm water from reaching the top of the radiator. In addition to the uneven heating of a warm bottom and cool top, a radiator may feel as if it is not working at all. If the radiator feels cool both on the bottom and top, there may be so much air that the water is not circulating at all. Air is introduced to the heating system when water is added as well as the action of the impeller pump. While bleeding may not fix all plumbing problems, it is the first remedy a heating engineer or plumber will attempt and if it is the problem, it will save you time and money on unncecessary plumbing bills.
Tools Needed To Bleed A Radiator
The only tools necessary to bleed a radiator are a bleed key and a rag or towel. The first step is to turn off the heat pump at the central source and open both valves at the bottom of the radiator. If the main heat pump is not turned off, it can draw more air into the system. Then, locate the bleed screw at the top of the radiator. Usually, the bleed screw is located at the ends of the radiator and occasionally on the back. Using the bleed key, turn the bleed screw anti clockwise; while bleeding, you will hear a hissing noise. Be prepared to tighten the bleed screw as soon as water starts dripping out of the bleed screw at the top of the radiator. Tighten the bleed screw by turning clockwise; do not over tighten the bleed screw. Occasionally the bleed screw has been damaged and the bleed key no longer works on the screw. In that case, carefully use a spanner to bleed the radiator.
Repeat the bleeding process on all radiators. Once the radiators are bled, if the heating system is a closed system, you will need to adjust the pressure by topping off the boiler. Once the system is turned on again, check each radiator for even heating, if the heat from the radiators is still uneven or insufficient, contact a heating engineer or plumber.
For Free Quotes From Local Plumbers And Other Local Tradesmen Click Here
Are You A Tradesman Looking For Jobs - Look No Further Than Top Tradespeople - go to http://www.toptradespeople.co.uk
In tough financial times it is important to try to save money on unnecessary home improvement bills for jobs which with a little bit of ‘insider’ knowledge you can do yourself to a very satisfactory standard. Minor jobs like bleeding radiators can save you substantial amounts of money on unncessary plumbing bills.
Bleeding A Radiator
Occasionally, you will notice a radiator heating unevenly. Specifically, the bottom of the radiator is warm while the top is cool. Before you call a heating engineer or plumber, try the simple and inexpensive remedy of bleeding the radiator to see if this will fix the problem. A radiator needs bleeding when air has infiltrated the system and is blocking the warm water from reaching the top of the radiator. In addition to the uneven heating of a warm bottom and cool top, a radiator may feel as if it is not working at all. If the radiator feels cool both on the bottom and top, there may be so much air that the water is not circulating at all. Air is introduced to the heating system when water is added as well as the action of the impeller pump. While bleeding may not fix all plumbing problems, it is the first remedy a heating engineer or plumber will attempt and if it is the problem, it will save you time and money on unncecessary plumbing bills.
Tools Needed To Bleed A Radiator
The only tools necessary to bleed a radiator are a bleed key and a rag or towel. The first step is to turn off the heat pump at the central source and open both valves at the bottom of the radiator. If the main heat pump is not turned off, it can draw more air into the system. Then, locate the bleed screw at the top of the radiator. Usually, the bleed screw is located at the ends of the radiator and occasionally on the back. Using the bleed key, turn the bleed screw anti clockwise; while bleeding, you will hear a hissing noise. Be prepared to tighten the bleed screw as soon as water starts dripping out of the bleed screw at the top of the radiator. Tighten the bleed screw by turning clockwise; do not over tighten the bleed screw. Occasionally the bleed screw has been damaged and the bleed key no longer works on the screw. In that case, carefully use a spanner to bleed the radiator.
Repeat the bleeding process on all radiators. Once the radiators are bled, if the heating system is a closed system, you will need to adjust the pressure by topping off the boiler. Once the system is turned on again, check each radiator for even heating, if the heat from the radiators is still uneven or insufficient, contact a heating engineer or plumber.
For Free Quotes From Local Plumbers And Other Local Tradesmen Click Here
Are You A Tradesman Looking For Jobs - Look No Further Than Top Tradespeople - go to http://www.toptradespeople.co.uk
25 Aug 2009
Tiling Tips - How to Grout Tiling For Your Tiling Job
Tiling grout strengthens the tile and keeps water from entering the joints. As well as the practical purpose of grout, it also adds aesthetically to the tiling project or job. Usually tiling grout is a neutral color but there are so many colors available now that any tiling grout color combination is possible. In general, it is best not to pick white or a light color for floor applications since dirt will quickly make it look dingy and you will end up with a mucky off white colour or yellowish tinge to your grout. This may lead to you having to repeat the grouting to your tiling job again.
Tiling grout application is actually a fairly simple job after the harder parts of laying and levelling the tile. The tools and equipment you need for your tiling grouting job are tiling grout, bucket, kneepads, tiling grout float, tiling grout sponge and waterproof gloves.
Tiling grout is available in premixed tiling grout form or in tiling grout powder form. The premixed tiling grout depends upon evaporation for drying and therefore is really only appropriate for small wall tiling applications which will not be in contact with water. The powder form of tiling grout is cement based and therefore dries chemically which provides a much stronger and harder joint. Powdered tiling grout is available in sanded or non-sanded mixtures. Sanded tiling grout is appropriate for tiling joints larger than 3mm and usually used for floor tiling applications. Non-sanded tiling grout is for wall tiling applications with a tiling joint width of less than 3 mm. It is possible to purchase a polymer-modified tiling grout or a tiling grout polymer additive, which adds flexibility and provides more water resistance but it is a little more difficult to work with on your tiling job. Polymer additives are indicated when the backing surface onto which your tiling is to be applied is wood since the wood will bend and flex and a polymer-modified grout will flex without cracking.
Tiling Grout Mixture - The first step to applying tiling grout is to mix the tiling grout. It is very important to use gloves, goggles and a mask when dealing with cement based tiling grout powders. The tiling grout bag has the proportion of water to tiling grout for mixing but factors such as heat will affect the mixture so add water only a little at a time to the tiling grout mix. The consistency of tiling grout should be about the same as peanut butter. A watery tiling grout mixture will take much longer to dry and is harder to work with. Once the tiling grout is mixed, it has a working time of 20-40 minutes so only mix small batches of your tiling grout or it will be necessary to throw away tiling grout and you will have to start your tiling job all over again.
Tiling Grout Application - Apply tiling grout to the tiling joints with a rubber tiling grout float. Press the tiling grout into the tiling joints by holding the tiling float at a 30-degree angle and applying pressure as tiling grout is dragged over the tiling gaps. Be sure that the tiling grout is filling the tiling joint to the bottom surface. Once the tiling grout fills all the tiling joints, scrape the excess tiling grout by holding the tiling float almost vertically as you drag. It is helpful to drag diagonally across the tiling joints to prevent digging in and accidentally removing tiling grout from within the tiling joints. Once the tiling grout has begun setting, use a large tiling sponge and wipe the excess from the tiling joints; do not use too much water in this process. Once the tiling grout hardens, go back with a soft rag and buff the tile to remove tiling grout film. Depending on the tiling application, the last step is a tiling grout sealer, which will help it repel stains and prolong the water-resistant life of your tiling grout and your overall tiling job.
http://www.toptradespeople.co.uk
Tiling grout application is actually a fairly simple job after the harder parts of laying and levelling the tile. The tools and equipment you need for your tiling grouting job are tiling grout, bucket, kneepads, tiling grout float, tiling grout sponge and waterproof gloves.
Tiling grout is available in premixed tiling grout form or in tiling grout powder form. The premixed tiling grout depends upon evaporation for drying and therefore is really only appropriate for small wall tiling applications which will not be in contact with water. The powder form of tiling grout is cement based and therefore dries chemically which provides a much stronger and harder joint. Powdered tiling grout is available in sanded or non-sanded mixtures. Sanded tiling grout is appropriate for tiling joints larger than 3mm and usually used for floor tiling applications. Non-sanded tiling grout is for wall tiling applications with a tiling joint width of less than 3 mm. It is possible to purchase a polymer-modified tiling grout or a tiling grout polymer additive, which adds flexibility and provides more water resistance but it is a little more difficult to work with on your tiling job. Polymer additives are indicated when the backing surface onto which your tiling is to be applied is wood since the wood will bend and flex and a polymer-modified grout will flex without cracking.
Tiling Grout Mixture - The first step to applying tiling grout is to mix the tiling grout. It is very important to use gloves, goggles and a mask when dealing with cement based tiling grout powders. The tiling grout bag has the proportion of water to tiling grout for mixing but factors such as heat will affect the mixture so add water only a little at a time to the tiling grout mix. The consistency of tiling grout should be about the same as peanut butter. A watery tiling grout mixture will take much longer to dry and is harder to work with. Once the tiling grout is mixed, it has a working time of 20-40 minutes so only mix small batches of your tiling grout or it will be necessary to throw away tiling grout and you will have to start your tiling job all over again.
Tiling Grout Application - Apply tiling grout to the tiling joints with a rubber tiling grout float. Press the tiling grout into the tiling joints by holding the tiling float at a 30-degree angle and applying pressure as tiling grout is dragged over the tiling gaps. Be sure that the tiling grout is filling the tiling joint to the bottom surface. Once the tiling grout fills all the tiling joints, scrape the excess tiling grout by holding the tiling float almost vertically as you drag. It is helpful to drag diagonally across the tiling joints to prevent digging in and accidentally removing tiling grout from within the tiling joints. Once the tiling grout has begun setting, use a large tiling sponge and wipe the excess from the tiling joints; do not use too much water in this process. Once the tiling grout hardens, go back with a soft rag and buff the tile to remove tiling grout film. Depending on the tiling application, the last step is a tiling grout sealer, which will help it repel stains and prolong the water-resistant life of your tiling grout and your overall tiling job.
http://www.toptradespeople.co.uk
11 Aug 2009
Tools Needed for Plastering
Prepping for Plaster is the most important step to have the plaster project turn out level and smooth. The tools needed for prep work include Plumb Level and Wood. In order to cut the wood to height you will need a Saw which can either be manual or electric. It will be helpful to also have on hand a few standard building tools before starting the project. You may need a Ladder, Claw Hammer and Buckets. Once the wooden guides are leveled and secured, the plaster can be mixed.
Plaster comes in two bases, cement base and gypsum based. Gypsum based plaster should only be used indoors as it will absorb moisture and is prone to mold. Cement based plaster is for exterior use. Plaster comes in powder form with all additives already in the bag so all that is needed is to add water and mix.
When mixing plaster the least expensive mixing tool is a wooden stick but if mixing a large amount, an electric mixer is a better option. A Mixer Paddle can be attached to a drill and will allow for a thorough mix with much less effort. It is important to mix only a small batch at a time since the plaster has a relatively short working time and cannot be used once it is too dry.
Transporting the plaster from the bucket to the project site is usually done a small batch at a time on a Hawk; a square metal plate with a handle centered underneath. Since plaster is heavy, be sure not to load the Hawk with more than you can comfortably balance and carry. The Hawk is used in conjunction with the Plasterers Trowel but since the Plasterers Trowel is metal and is prone to rusting, an alternative is a polycarbonate Float. The Float or Trowel is used to scoop plaster from the Hawk and apply the plaster to the project surface. A Plasterers Darby is used to smooth the plaster to the correct depth. A Darby is a long metal straight edge with handles which spans the plaster surface and rests on the wooden guides, as it is pulled along the guides it levels the plaster to the finished depth. An alternative to the Darby is a Featheredge which is a long aluminum straight edge also useful for plasterboard applications.
Another tool that is helpful is a Splash Brush. A Splash Brush can be an old paint brush or a wall paper brush. The splash brush is used to keep the plaster from drying out but if left too long, the plaster will become hard and unstable and should not be used. One last tip is to keep all plaster tools clean and free of plaster bits, chips or chunks; any old plaster bits on tools will ruin a smooth finish.
Plaster comes in two bases, cement base and gypsum based. Gypsum based plaster should only be used indoors as it will absorb moisture and is prone to mold. Cement based plaster is for exterior use. Plaster comes in powder form with all additives already in the bag so all that is needed is to add water and mix.
When mixing plaster the least expensive mixing tool is a wooden stick but if mixing a large amount, an electric mixer is a better option. A Mixer Paddle can be attached to a drill and will allow for a thorough mix with much less effort. It is important to mix only a small batch at a time since the plaster has a relatively short working time and cannot be used once it is too dry.
Transporting the plaster from the bucket to the project site is usually done a small batch at a time on a Hawk; a square metal plate with a handle centered underneath. Since plaster is heavy, be sure not to load the Hawk with more than you can comfortably balance and carry. The Hawk is used in conjunction with the Plasterers Trowel but since the Plasterers Trowel is metal and is prone to rusting, an alternative is a polycarbonate Float. The Float or Trowel is used to scoop plaster from the Hawk and apply the plaster to the project surface. A Plasterers Darby is used to smooth the plaster to the correct depth. A Darby is a long metal straight edge with handles which spans the plaster surface and rests on the wooden guides, as it is pulled along the guides it levels the plaster to the finished depth. An alternative to the Darby is a Featheredge which is a long aluminum straight edge also useful for plasterboard applications.
Another tool that is helpful is a Splash Brush. A Splash Brush can be an old paint brush or a wall paper brush. The splash brush is used to keep the plaster from drying out but if left too long, the plaster will become hard and unstable and should not be used. One last tip is to keep all plaster tools clean and free of plaster bits, chips or chunks; any old plaster bits on tools will ruin a smooth finish.
Subscribe to:
Posts (Atom)